Haman
I'm not really sure what you mean?
Mapping the display to itself is just a method to check the underlying linearity of the display.
It shows if there are unexpected issues BEFORE you start calibrating.
And it can be done with any profile, but the more points, the more information you have to assess.

Steve

Steve
Steve,
I apologize in advance if my understanding or explanation is poor.

In the video, you did a brightness and contrast setup with 100% white luminance of around 104 nits to get the current un-calibrated state. Then you made adjustment to improve the Dif EOTF with point 3 and to get an initial starting point with running Grey Only Large, but I did not hear you mentioning or adjusting the RGB High/Gain for 100% white to closely match D65. From 15:00 onwards, you extracted the colour space from the initial starting point for that specific TV, selected the new colourspace and the RGB balance looks better. Proceed to run a 21^3 cube profile and re-measured a few of the tangents points (> dE 5).

Can I use the same method above and use the new profile (17^3) to create the 3D LUT needed for my TV?

My current profiling using the general method in AVS, has many red and orange points inside the Rec709 target.
From AVS : Native Gamut on TV, native Gamma preset 2.2, Perform only Contrast Brightness check, and pre-calibrate only 100% White for my TV, 109% for LG SM, run Primary only, after that start profiling.

The 'adjustment' was to better set the blacks 'clip point', and correct better the initial over-bright response of the display.
I made no attempt to set the colour temp, beyond that of the display's native setting, as the LUT will do that.

The extracted colour space is then matched to the underlying setting of the display, to see how well it 'maps' to itself.

All that has nothing to do with the large profile performed, and the LUT generated from it.
That is totally separate.
The 'mapping' the display to itself is just a check to see if there is anything screwy with the display in it's native state.

Steve

Steve
Thank you. I re-watched that video a few times again and I think I got what you mean now.

"The 'adjustment' was to better set the blacks 'clip point', and correct better the initial over-bright response of the display.
I made no attempt to set the colour temp, beyond that of the display's native setting, as the LUT will do that."
This is something I will try as well.

Hi, how does the Profile Luma target works? Specifically, when do we enable "Auto" and when do we not enable it? What conditions do we want to enable and not enable it? Thanks.

That is actually up to you...
There is no single answer, as it all depends on what you are trying to do when measuring/profiling.
For example, if you are trying to adjust a display to meet a specific set of luma levels for Min/Max, you would not tick the Auto box.
If the display min/max values are not to be adjusted, and you want to see the relative accuracy of all other values to the display's min/max, you would tick the Auto box.

Steve

Hi, after I uploaded my daytime 3D LUT generation and completed 10^3 verification test, I was left with around 50 orange points and 0 red point. I then re-measured the 50 points by selecting those points and close to half of them were gone. May I know why it happened this way? Is there a need to re-measure the orange or red points after the verification test? Probe settings (integration, Intelligent, delay) were the same as the LG guide. My i1Display Pro Plus was placed non-contact (around 8cm) to TV. Thanks.

Likely just means the TV is unstable, as WOLEDs are.
Or, it is possible that that Extra Delay is set too short, as when doing manual re-measurements you will have the patch displayed for some time before you measure.

Steve

I'm really enjoying ColourSpace ZRO as an alternative to HCFR.

I noticed with ZRO that I could save user profiles within a session, but as soon as I quit the app and relaunch, all user profiles are gone. Is this a limitation of the free version? User color spaces are saved and retained as expected.

Sorry, measured Profiles are NOT saved.
That is a limitation of ZRO, as defined in the Features Matrix of the website.
https://www.lightillusion.com/colourspace.html#matrix-1

But, user defined colour spaces are saved, if you have the latest ZRO version.
The latest version of ZRO (or any other software) can always bee checked via the Software Downloads page of the website.

ColourSpace DPS includes additional features, including 3D Graphs, and will also have Report capability, when that is added to ColourSpace.
(A very useful additional capability is LUT Generation, for additional display assessment within ColourSpace DPS.)

Steve

Thanks for the clarification, Steve.

I figured the details had to be on your website somewhere, I just couldn't find it.