| Forums | Register | Reply | Polls | Search | Statistics |
Display Calibration Light Illusion Forums / Display Calibration /  
 

i1D3 OEM integration

 
Author alex_t
ZRO
#1 | Posted: 8 Sep 2013 14:17 
Hi !

I need some help to set my i1D3 OEM inside Light Space CMS HCL.

What are the best values for:

Integration Time
Extra Delay Time
Display Type
Calibration settings

I use a JVC X35 (video projector DILA) in a very dark room.

Thanks

Author Steve

INF
Male
#2 | Posted: 9 Sep 2013 15:22 
Hi Alex,
I have replied to you e-mail question too.

But, D-ILA technology is rather unstable, so I would use 'Burst' mode, with a 1.75 sec integration time, no extra delay, and with Av. low light on.

Does that help?

Steve
Steve Shaw
Mob Boss at Light Illusion

Author alex_t
ZRO
#3 | Posted: 9 Sep 2013 21:40 
Hi Steve,

Many thanks Your software is awesome !

Author Harry
ZRO
#4 | Posted: 14 Sep 2013 08:52 | Edited by: Harry 
For the "Integration Time" you can also try to optimize using this little formula:
100 x (1 / fps)

So for using the i1D3, and in case of displaying
-> 24hz = 4s, but it's ok to use 2s instead of.
-> 50hz = 2s
-> 60hz = 1,75s or maybe 1,5s

JVC's CMD / MPC (4k sim on X55/75/95) should be switched off.

Please note: LS has an internal probe reading start delay time of 0,5s (hard coded)
For my JVC X75 I prefere to set "Extra Delay Time" at 0,5s so in total it is 1s delay before the probe starts reading.
With that I got very stable readings.

And "burst" was also ok for my i1D3 (off screen measurements)

Harry

Author alex_t
ZRO
#5 | Posted: 14 Sep 2013 12:28 
Thanks Harry

I'm doing a full profile in 1080p60 with 1.75s for the "Integration Time". I'll try your settings later on.

Regards
alex

Author BeTru
ZRO
#6 | Posted: 17 Oct 2013 16:48 | Edited by: BeTru 
Sorry to bump an old thread

I have a similar question as the op with regards i1D3 values. I would like to know please what settings I should use for a Pioneer KRP-600a Plasma and a soon to be purchased Sony VW500es projector. Both in a batcave environment

Many Thanks

Ben

Author Steve

INF
Male
#7 | Posted: 17 Oct 2013 18:11 
Hi,

There are no 'set' setting for the probe.
Some displays require some settings, other will be different.

With Plasmas we suggest non-contact mode with 'Burst' mode, and use the formula shown in the user manual to find the best 'integration' time.
See: http://www.lightillusion.com/forums/index.php?action=vthread&forum=8&topic=131

With projectors use settings that match the projector technology, again in non-contact mode.
Burst mode will probably be best, with an integration time approx. 1.75.

Steve
Steve Shaw
Mob Boss at Light Illusion

Author BeTru
ZRO
#8 | Posted: 17 Oct 2013 18:35 
Thanks Steve

Hoping to have a run through tomorrow must have about 15 tabs open in the browser at the min. I'm trying to read through as much as possible before then

Ben

Display Calibration Light Illusion Forums / Display Calibration /
 i1D3 OEM integration

Your Reply Click this icon to move up to the quoted message


Watch this topic / Get updates by Email
 (?)
Only registered users are allowed to post here. Please, enter your username/password details when posting a message, or register first.

 

 
Online now: Guests - 1
Members - 2 [ Omardris, Steve ]
Max. ever online: 312 [11 Jun 2021 17:33]
Guests - 312 / Members - 0